Heavy Duty Self Drilling Screw No.5 Point Drills 12.7mm Steel Plate Hex Washer Head
No.5 point heavy duty self drilling screw that drills and taps through 12.7mm steel plate in one pass. SCM435 structural grade body, hex washer head, zinc or Ruspert coated.
Heavy Duty Self Drilling Screw
,12.7mm Steel Plate Drill Point
,Structural Grade Hex Washer Head
One pass through 12.7 mm (1/2") steel plate. Structural-grade fastening without pre-drilling.
A #2 or #3 point tops out around 2–3 mm of steel, and even a #4 point stops at roughly 6.5 mm. This screw is built around a #5 drill point — a longer, thicker pilot section with a reinforced flute — so it cuts and taps its own hole through 12.7 mm of hot-rolled steel plate in a single pass. No pilot hole, no step drilling, no bit change halfway through the flange.
- Single-pass capacity: 12.7 mm steel plate, tested on 300 MPa and 400 MPa structural plate.
- Structural-grade body: SCM435 alloy steel, case hardened to HV 560–620 with a tough core, so the shank does not shear under impact drivers.
- Hex washer head: 8 mm hex drive with an integrated bonded washer that spreads clamp load and seals the hole against water ingress.
- Wing-free self drilling: no wings to snap off, so the thread engages cleanly in metal-to-metal assemblies.
Steel frame and purlin connections, container and trailer bodies, cold-formed steel studs, mezzanine decking, solar mounting rails, HVAC duct hangers, guardrail brackets and heavy gauge cladding where the substrate is thicker than a standard self drilling screw can handle.
| Drill Point | No.5 (12.7 mm steel drilling capacity) |
| Point diameter / point length | 5.5 mm / 12–14 mm |
| Material | SCM435 / 10B21 alloy steel |
| Head Type | Hex washer head (with bonded EPDM washer) |
| Drive | 8 mm (5/16 in) hex; Torx T30 available |
| Diameter | ST5.5 – ST6.3 (#12 – #14) |
| Length | 25 – 200 mm (No.5 point requires 25 mm minimum) |
| Thread | Fine self-tapping, full thread up to 50 mm; partial thread above |
| Case hardness | HV 560 – 620 (HRC 53–56) |
| Core Hardness | HV 250 – 400 (HRC 22–40) |
| Case depth | 0.05 – 0.15 mm |
| Finish | Zinc plated (96–200 h) / Ruspert 1000 (1000 h) / Ruspert 3000 (3000 h) / Dacromet (~500 h) |
| Standard | DIN 7504 K, IFI 502 / ASME B18.6.4, or drawing |
| Tolerance | Diameter and length per DIN 7504; ±1.0 mm on length unless drawing specifies |
Raw material certificate → heading → thread rolling → heat treatment → surface treatment → salt spray test → torque and drill-through test on 12.7 mm plate → sorting and packing. Drill-through and drive torque are re-checked on a sampling basis before shipment, and material certificates travel with the goods.
Bulk carton, small box, or blister pack; export grade carton on plywood pallet with desiccant. Free samples of standard sizes — buyer covers freight. Stock sizes ship in 7–15 days, production runs in 15–25 days.
Bonded Washer Self Drilling Screw Stainless Steel 304/316 and SCM435 Material Hexgon Head
Bi Metal Self Drilling Screw With Alloy Steel Tip Fusion Customized Standard
Thread Washer Head Self Drilling Screw Stailess Steel External Hex Drive